AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateTrusted Furnace Replacement for Burbank Homeowners
When a furnace starts failing in December, the problem isn’t just discomfort. In Burbank‘s older single-family homes and post-war apartment conversions, a dying furnace often means a scramble to find someone who knows the equipment already bolted to your closet floor or garage wall. We specialize in furnace replacement, which means we’re not splitting our attention across plumbing or roofing. Our technicians have up to 8 years of experience, and we’re factory-familiar with 9 leading brands, so we know the failure points on the Trane or Lennox unit you’re staring at right now. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Call (844) 962-2046 and we’ll give you a straight answer on repair versus replacement.
What Our Furnace Replacement Service Includes
Full Heating System Assessment
Before we quote a replacement, we run a full assessment of your existing system: the furnace itself, the ductwork feeding each room, the thermostat wiring, and the electrical or gas connections. This matters because a furnace that’s “failed” sometimes has a duct problem or a thermostat fault masquerading as a dead heat exchanger. We give you the diagnosis first, then tell you honestly whether a repair buys you another few seasons or whether replacement is the smarter money. If a repair makes sense, we’ll say so.

System Sizing and Load Calculation
Replacing a furnace with the same size unit isn’t always right, especially in Burbank homes where additions, window upgrades or attic conversions have changed the heating load since the original install. We calculate the proper capacity for your home’s square footage, insulation, window area, and duct layout rather than guessing from the old nameplate. An oversized furnace short-cycles, wastes gas, and wears out faster; an undersized one never keeps up on the coldest mornings. Getting this right is the single biggest factor in how the next 15 years go.

Removal and Safe Disposal of the Old Unit
Pulling out a furnace means disconnecting gas lines, electrical feeds, and the flue or venting, then hauling a heavy unit out of a tight closet or attic access without damaging walls or ductwork. We handle the disconnection, removal, and proper disposal of the old equipment. If your old unit contains components that require special handling, we take care of that too, so you’re not stuck figuring out what to do with a 150-pound appliance in your garage.

New Furnace Installation and Commissioning
Installation covers setting the new unit, connecting gas and electrical, sealing the plenum and duct connections, and installing or adapting the venting to match the new furnace’s requirements. We then commission the system: checking gas pressure, verifying airflow, testing the thermostat through a full heat cycle, and confirming the safety switches work. You get a walkthrough of the new equipment and the controls before we leave. Our work spans the full equipment lifecycle, so when this furnace eventually needs a repair, you’re calling the same people who installed it.
Post-Install Verification and Documentation
After the install, we document what was done: the model and serial number of the new unit, the settings we used, and any duct or venting changes. That record matters when you sell the home or file a warranty claim. We also walk you through filter location, filter size, and how often to change it in Burbank’s dusty spring air, since a clogged filter is the most common reason a new furnace underperforms in its first year.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Brands We Service for Furnace Replacement
We work on the system you already have, and that includes the major brands most Burbank homes were built or retrofitted with. Trane equipment tends to be robust but has specific control board and inducer motor behavior we’ve learned to read quickly during diagnosis. Lennox furnaces show up frequently in this area, and we know where their heat exchangers and pressure switches tend to fail as they age. Goodman units are common in value-focused installations, and we know their airflow characteristics and common ignition faults well enough to skip the guesswork.
Rheem furnaces turn up in a lot of the older housing stock around Burbank, and their venting and gas valve configurations reward someone who’s worked on them before. We’re also familiar with Carrier, York, Daikin, Bryant, and American Standard equipment, so whether you have a Rheem or any other make, we can help. We’re not a dealer pushing one line. We replace what’s there with something that fits your home and your budget, and we tell you when a brand you already trust is the right call.
Signs You Need Furnace Replacement Right Now
- The furnace is 15 years old or older and repairs are stacking up. A furnace past its expected service life can still run, but each repair costs more than the last and the efficiency losses quietly eat your gas bill. When you’re calling for a fix every season, replacement usually costs less over the next five years than keeping the old unit alive.
- You smell gas or notice soot or corrosion around the unit. A gas smell, yellow instead of blue flame, or soot streaks near the furnace point to a combustion or venting problem that needs immediate professional attention. Don’t run the system while you wait; shut it off at the thermostat and call a trained technician. This is a safety issue, not a maintenance item.
- The heat never reaches the far rooms, or the house feels cold even with the furnace running. This can be a sizing problem, a duct problem, or a blower on its way out. If you’ve already tried balancing the vents and it hasn’t helped, a proper assessment tells you whether the furnace itself is the culprit.
- Your gas bills jumped and the house isn’t any warmer. A furnace loses efficiency as its heat exchanger degrades and its burners foul. If you’re paying more for the same comfort, the unit is telling you something.
- The furnace short-cycles, bangs, or shuts off before reaching temperature. Repeated short cycling stresses every component and often signals a failing limit switch or a blocked flue. It’s also a sign the unit may be oversized for the ductwork, which a replacement with proper sizing can solve.
Our Furnace Replacement Process – Step by Step
- 1
Diagnostic visit and honest recommendation. We inspect the furnace, test the ignition sequence, check gas pressure, and look at the heat exchanger and venting. We also look at your ductwork and thermostat. Then we tell you plainly whether a repair makes sense or whether replacement is the better move, with the reasoning behind it.
- 2
Load calculation and written fixed-price quote. We measure your home and calculate the heating capacity it actually needs, then put a fixed price in writing before any work starts. The quote covers the equipment, labor, removal and disposal of the old unit, and any venting or duct adaptation required.
- 3
Equipment selection and scheduling. We walk you through unit options that fit your home, your budget, and the fuel type you already have, and you pick. Then we set an installation date that works for you. This is scheduled work, not same-day work, because the unit has to be ordered and the install has to be done right.
- 4
Installation day. We protect the work area, disconnect and remove the old furnace, set and connect the new unit, seal the duct connections, and verify the venting. We test gas pressure and airflow, then run the system through a complete heat cycle to confirm it’s operating safely and to spec.
- 5
Walkthrough and handoff. We show you the new equipment, the controls, and the filter location, and we leave you with the documentation on what was installed. If you have questions about the system a month later, call us. We answer 24/7.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Furnace Replacement Cost in Burbank?
Furnace replacement in Burbank typically falls in the same range as our AC installation work, roughly $3,500 – $7,500 depending on the equipment and the complexity of the install. A straightforward swap in a standard closet with matching ductwork sits near the low end. Higher-efficiency equipment, a harder location like a tight attic, new venting, or duct modifications push toward the upper end. If your furnace only needs a repair rather than replacement, that’s a separate job and typically runs $150 – $700 for furnace repair in Burbank.
What affects the price most: the efficiency rating and brand of the new unit, whether the venting needs to be changed, whether the electrical feed needs an upgrade, and whether the ductwork needs sealing or modification. You avoid overpaying by getting a written fixed price before work begins and by asking whether the quote includes removal and disposal of the old unit; ours does. Our free estimate includes a load calculation, a walkthrough of the unit options, and a written price that doesn’t change unless you change the scope. The written estimate sets the final price.
Furnace Replacement Near Burbank – Our Service Area
We work throughout Burbank and the surrounding neighborhoods, including Magnolia Park, Toluca Lake, and the Rancho Adjacent area, plus nearby cities like San Fernando, Glendale, and North Hollywood. We also serve Beverly Hills and the Westside for scheduled installations. Furnace replacement is planned work, so we schedule the install date with you and confirm the window in advance. For breakdowns, fast dispatch from 7am to 7pm gets a technician to you quickly, and our AC Repair Burbank team handles AC installation and furnace repair as well.
Serving Burbank, CA – Our Local Coverage Area
We serve Burbank and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Furnace Replacement in Burbank
Furnace replacement means removing your old heating unit entirely and installing a new one. A repair fixes a specific failed component, like an igniter, a blower motor, or a control board. Replacement is the right call when the unit is old enough that repairs keep stacking up, when the heat exchanger has failed, or when the cost of repairs approaches the cost of new equipment. We diagnose first and tell you which one actually makes sense for your situation.
A standard furnace replacement takes most of a day, typically 4 to 8 hours once the crew arrives with the new unit. Straightforward closet installations move faster; attic units, new venting, or duct modifications add time. We give you a realistic window when we schedule, and we don’t leave the job until the system has been tested through a full heat cycle and you’ve had the walkthrough. Call (844) 962-2046 to get a scheduling estimate.
Typical furnace replacement in Burbank runs about $3,500 – $7,500, depending on the equipment, efficiency rating, and installation complexity. That range covers removal and disposal of the old unit, the new furnace, labor, and standard venting. Additions like new ductwork or electrical upgrades are quoted separately. The written estimate sets the final price, and our estimates are free. Call (844) 962-2046 for an exact quote.
Yes. We work on Trane, Lennox, Goodman, and Rheem furnaces, along with Carrier, York, Daikin, Bryant, and American Standard. That’s 9 major brands total, and our technicians are familiar with how each one is built and where it tends to wear. We service the system you already have rather than steering you toward a brand we prefer. If you’re not sure what you have, we can identify it during the diagnostic visit.
Furnace replacement is scheduled work, not same-day work, because the new unit has to be ordered and the installation has to be done properly. But we do offer same-day diagnosis for a furnace that’s failing, so you’re not waiting days to learn where you stand. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (844) 962-2046 and we’ll get you on the schedule.
Warranty terms depend on the equipment manufacturer, so the coverage on your new furnace comes from the brand you choose. We walk you through the warranty terms for each unit option before you decide, so there are no surprises later. We also document the installation details, which you’ll need for any warranty claim. Ask us about the specific warranty on any unit during your free estimate.
Clear access to the furnace and the path the crew will carry the new unit in, and move anything fragile away from the work area. If the furnace is in a closet, empty the surrounding space so we can work without moving your belongings. Keep pets and kids clear of the work zone while we’re connecting gas and running tests. And plan to be home for the walkthrough at the end so you can ask questions about the new system.
Schedule Your Furnace Replacement Service in Burbank Today
If your furnace is on its last legs, don’t wait for the coldest week of the year to deal with it. Call (844) 962-2046 for a free estimate and a straight answer on repair versus replacement. We work on the system you already have, we’re familiar with the major brands, and our estimates include a load calculation and a written fixed price. We answer 24/7, and for breakdowns, fast dispatch from 7am to 7pm, Sunday through Friday. Remember, we also handle furnace repair when a fix is the better move.
Written by the team at AC Repair Burbank.